LOGAMATIC 4121 PDF

Download the catalogue and request prices of Logamatic By buderus, heat regulation and hygrometric control, logamatic Collection. Manuals and User Guides for Buderus Logamatic We have 1 Buderus Logamatic manual available for free PDF download: Operating Instructions . View and Download Buderus Logamatic operating instructions manual online. Logamatic Control Unit pdf manual download. Also for: Logamatic.

Author: Gumuro Nalkree
Country: Bahrain
Language: English (Spanish)
Genre: Environment
Published (Last): 26 December 2015
Pages: 369
PDF File Size: 3.1 Mb
ePub File Size: 7.24 Mb
ISBN: 926-9-36951-739-4
Downloads: 12134
Price: Free* [*Free Regsitration Required]
Uploader: Goltilrajas

It changes over between day mode standard mode and night mode setback mode. The “OFF” switching point for Monday appears.

The mixer is switched volt-free. Manually disconnect the heating circuit mixer and position towards hotter or colder, until the required room temperature is achieved.

Products by BUDERUS Logamatic Collection | Archiproducts

The displayed temperature depends on the set room temperature. Selecting A Standard Program here “Senior program”.

Seniors The display shows the program designation and the first switching point for the selected heating program here “Senior program”. Your heating program will now operate according to your “Own program”. If the switches are not set lovamatic automatic, a corresponding message appears on the MEC2 programming unit, and the fault indicator illuminates.

To connect two consecutive heating phases, place the stop point of the first heating phase onto the start point of the next loggamatic. This pump enables the second heating circuit to be operated independently of the first heating circuit. If you want to change a setting, e. Page 48 – Setting the holiday function Page 49 Page 50 – Interrupting and continuing the holiday Open windows three to four times a day for approximately 5 minutes.

  LEI 11274 PDF

CONTROL PANEL FOR WALL-MOUNTED AND FLOOR-STANDING BOILER

The design and operation of this product conform to European Directives and the supplementary national requirements. Press “Night mode” to switch off DHW circulation. The cylinder primary pump and DHW circulation pump if installed run constantly logammatic thermal disinfection.

Manually adjust the mixer. Current functions are indicated by LEDs. Your heating program will now operate according to your “Own program”.

Page 35 “Night mode”. Your heating system will constantly operate in summer mode.

Logamatic 4121

Holiday days 5 Release “Temp” to save your input. Manual Mode Logamatic Notify your contractor of the faults displayed on the MEC, or the fault code on the boiler. You will learn how to create a new heating program which accurately matches your personal circumstances.

Only clean the control unit with a damp cloth. In this case all switching points for the heating phase remain active. Select a heating circuit here: The lower the outside temperature, the higher the flow temperature must be. After a delay, it automatically changes over between summer and winter mode. If the electronics fail, the control unit can operate in emergency mode. The party function starts immediately.

Set the required room temperature by turning the rotary selector. The control unit, which is regulated by the MEC2 programming unit, is set up at the factory for immediate use. In emergency mode, all pumps continue to run and the mixers are volt-free. Setup Report Heating circ. Summary of standard programs.

  F55 POLAR PDF

Set the required room temperature 44121 turning the rotary selector. The heat demand of a room largely depends on the following factors: With this kind of control you always need to keep all thermostatic radiator valves in the reference room fully open. The modified switching point will be saved under the “Own” program and lofamatic number of the heating circuit here “2”.

The burner [2] heats the water inside the boiler [1]. Ask your heating contractor whether this function has been enabled. Some functions which you may need are located behind a flap. Introduction Your heating system offers a wealth of further useful functions.

The “Day mode” LED illuminates. Several of these modules can be used in one control unit. This saving is not shown on the display. Your modified program will be saved under the program name “Own” logajatic the number of the heating circuit. Setting the time Hold down “Time”, and select the required time with the rotary selector. Hold down “Heating circuit”, and select the required heating circuit with the rotary selector here: