CD4018B DATASHEET PDF

DESCRIPTION. The HCFB is a monolithic integrated circuit fabricated in Metal Oxide Semiconductor technology available in DIP and SOP packages. Data sheet acquired from Harris Semiconductor. SCHSC − Revised October The CDB types are supplied in lead hermetic dual-in-line. CDB datasheet, CDB pdf, CDB data sheet, datasheet, data sheet, pdf, Texas Instruments, CMOS Presettable Divide-By-N Counter.

Author: Goltigul Kemi
Country: Argentina
Language: English (Spanish)
Genre: Business
Published (Last): 16 January 2017
Pages: 118
PDF File Size: 11.30 Mb
ePub File Size: 15.49 Mb
ISBN: 479-6-56364-283-8
Downloads: 6539
Price: Free* [*Free Regsitration Required]
Uploader: Tagal

If I end up making more of these, do you know if there’s a equivalent cd401b the ? You could add isolating diodes so that you do not have that worry. You can use the DIP switch and diodes to provide the same sort of count selector, or just stick with binary input. I assume you are careful to make sure that only one of the Dip switches is on at a time.

Second problem was that, probably because of the low voltage of the littlebits power supply, the AND gate output wasn’t pushing enough current to drive the data in on the I would be particularly interested in knowing what the proper value of the resistor between the emitter and ground should be.

(PDF) CDB Datasheet PDF Download – CMOS PRESETTABLE DIVIDE-BY-N COUNTER

Regarding the transistor though, whether it should be able to or not, the is capable of driving both an output led and triggering a littlebits microsquencer straight from the data pin, as long as it’s doing an even division. Sorry for the schematic, I drew it up in MSPaint and it has been a while cd4018n I’ve drawn a schematic.

  CARDSHARING MIT CCCAM FAQ PDF

Cd4018g data pin on the will work fine from the common of the dip switch.

Trigger pulse goes in and, depending on how it’s set, for every x pulses in you get 1 pulse out. The datasheet uses Nand followed by invertor to get the AND functionality.

CDB Datasheet PDF – Texas Instruments

I could not, however, run the output of a to the data pin with any success unless I first amplified it. Use invertor between carry out and load to load the start value into the counter when it rolls over.

Basically it’s a straight datasheet functionality of a cd divide by n counter. I would use a 74LS which is a synchronous counter that fatasheet be programmed. I made it mostly for driving microsequencers at “triplet” rates.

You’re right about the datasheet, I missed the dot on the tip of the gate, mea culpa. I datasheef the last two evenings putting this together on a breadboard.

(PDF) CD4018B Datasheet download

The hard part comes in that if you want to divide by odd numbers, you need to throw in some external logic. A 74LS08 has more output drive with a slightly different pin cd401b.

  INSTRUMENTATION AND ORCHESTRATION BLATTER PDF

Thanks for the response. Would appreciate any feedback before I commit it to perf board and build a second one. If anyone cares to give it a good proof reading, again, it would be appreciated.

Everything is also made a bit more difficult by the output being part of the feedback that determines the division rate.

Datasheet «CD4018B»

If you want to be more flexible, a simple atmega P chip can be used and programmed to provide any cd4018 you want to output. A selector switch would’ve been a lot better than a dip switch, but it was readily available. You can buy binary encoded switches Your arduino midi interface is actually next on the build list.

The carry out is always 1 clock pulse wide. This was fixed by the addition of a -very- mickey mouse transistor amp stage. First problem was that the data sheet says to tie the outputs together with a NAND gate The is a twisted ring counter, there datashdet several ttl programmable counters.