Triacs. BT series E sensitive gate. GENERAL DESCRIPTION. QUICK REFERENCE DATA. Passivated, sensitive gate triacs in a. SYMBOL PARAMETER. BT Datasheet, BT 4A V TRIAC Datasheet, buy BT Buy BTD, 4A, V, TRIAC, Gate Trigger V 10mA, 3-pin, Through Hole, TOAB NXP BTD, Browse our latest triacs offers.

Author: Yozshumi Vudosar
Country: Puerto Rico
Language: English (Spanish)
Genre: Love
Published (Last): 18 March 2007
Pages: 374
PDF File Size: 15.23 Mb
ePub File Size: 2.35 Mb
ISBN: 458-9-68564-398-3
Downloads: 67713
Price: Free* [*Free Regsitration Required]
Uploader: Kazile

In particular, TRIAC always has tb136 small current flowing directly from the gate to MT1 through the p-silicon without passing through the p-n junction between the base and the emitter of the equivalent NPN transistor. Low-power TRIACs are used in many applications such as light dimmersspeed controls for electric fans and other electric motorsand in the modern computerized control circuits of many household small and major appliances. Figure 5 shows the triggering process.

Power management RF technology Test Wireless. When mains voltage TRIACs are triggered tric microcontrollers, optoisolators are frequently used; for example optotriacs can be used to control the gate current. The gate threshold voltage of the BT is also very less so can be driven by digital circuits.

It provides AC switching for electrical systems. A high rate of rise of the triad between MT1 and MT2 in either direction when the device is turning on can damage or destroy the TRIAC even if the pulse duration is very short. This page was last edited on 26 Julyat This creates additional harmonics which is not good for EMC performance and also provides an imbalance in the system. During the remaining half no conduction occurs and accordingly only half the waveform can be utilised.


TRIAC | What is a TRIAC? | TRIAC Circuit |

Capacitor types Ceramic resonator Crystal oscillator Inductor Parametron Relay reed relay mercury switch. TRIAC symbol for circuit diagrams.

The N region attached to MT2 is active, but the N region attached to MT1 only participates in the initial triggering, not the bulk current flow. TL — Programmable Reference Voltage.

BTE TRIAC Pinout, Equivalent, Specifications & Datasheet

Complete Technical Details can be found in the datasheet present at the end of this page. The process uses a remote gate control and is illustrated in Figure 7.

They are typically in the order of some milliamperes. It is effectively a development of the SCR or thyristor, but unlike the thyristor which is only able to conduct in one direction, the TRIAC is a bidirectional device. So if you looking to switch of control dim, speed control an AC load which consumes less than 6A with a digital device like microcontroller or microprocessor then BT might be the right for you.

When requiring to switch both halves of an AC waveform there are two options that are normally considered. Other than controlling through switch the BT can also be controlled through a microcontroller or a microprocessor.

These are the Gate and two other terminals are often referred to as an “Anode” or “Main Terminal”. However when using a TRIAC, it is necessary to be aware of its limitations so that these can be satisfactorily addressed and overcome should they affect the operation of the overall circuit in any significant way.


When used to control reactive inductive or capacitive loads, care must be taken to ensure that the TRIAC turns off correctly at the end of each half-cycle of the AC in the main circuit.

Features Maximum Terminal current: The fact that the TRIAC can be used to control current switching on both halves of an alternating waveform allows much better power utilisation.

Seen from the outside it may be viewed as two back to back thyristors and this is what the circuit symbol indicates. Other three-quadrant TRIACs can operate with smaller gate-current to be directly driven by logic level components. Broadcast technology Embedded Design principles Distribution Formulae.

What is a TRIAC – Tutorial

Its formal name is bidirectional triode thyristor or bilateral triode thyristor. Because each SCR will have an entire half-cycle of reverse polarity voltage applied to it, turn-off of the SCRs is assured, no matter what the character of the load. They find particular use for circuits in light dimmers, etc. Suppose one wants to turn the inductor off: Thus, the triggering scheme is the same as an SCR.